PescaSubacquea.net › Forum › Attrezzature › Fucili Oleopneumatici › Una semplice ed economica tenuta stagna con sviluppi inter..
-
AutorePost
-
12 Agosto 2013 alle 8:25 #12897020DaniloPartecipante
Come da titolo questa e’ la realizzazione semplice e molto economica con sviluppi interessanti.
La tenuta e’ fatta, in questo caso, con un semplice tubo in silicone da 6mm, sicuramente andrebbe meglio un tubo in EPDM o, meglio ancora, in PTFE. Purtroppo, mm 6.0, e’ la misura
piu’ vicina al 6.5 che avevo trovato, in America vendono il tubo da 1/4 pari a mm 6.35 che dovrebbe essere la misura piu confacente. Il grande vantaggio di questo sistema, oltre a essere economico, e’ che si possono sparare aste da 6.5, 6.75, 7mm sia nude che con codolo solo variando con le mani, nulla ci vieta di poterlo fare con un meccanismo, l’altezza del tubo sul nottolino.In pratica, piu’ si fa “calzare” il tubo sul nottolino e piu’ la bocca del tubicino si allarga in modo da modulare una diversa larghezza in base alle aste che adotteremo. Inoltre, questo sistema, visto l’angolazione accentuata del tubo sull’asta, dovrebbe risultare meno esposta alla pressione esercitata dall’acqua in profondita’. La tenuta e’ garantita e testata nella mia “potentissima” camera iperbarica, purtroppo non e’ mai stata provata in acqua, quindi, l’effettiva durata o la corretta funzionalita’ sono ancora tutte da verificare.
Le foto allegate mostrano 2 diverse misure per aste da 6.5 e 7 mm realizzate semplicemente facendo indietreggiare il tubicino sul nottolino.
12 Agosto 2013 alle 10:09 #311840lulazzPartecipanteora ci devi dire come lo blocchi in testata senza farlo sparare via al primo tiro
hai previsto anche un oring alla base del nottolino per fargli fare il tenuta con la volata?
in quel caso si potrebbe usare come scorrisagola
oppure legarlo da qualche parte con asta nuda
e riposizionarlo al prossimo caricamento12 Agosto 2013 alle 11:19 #311841TekelPartecipanteOccorre anche tagliare il tubo a tornio per avere il margine estremo con precisione sufficiente a garantire continuità di aderenza attorno all’asta; basta davvero poco per allagare la canna.
Interessante, ma per accogliere il tutto hai progettato una testata ad hoc oppure è adattabile ad un modello commerciale?12 Agosto 2013 alle 12:32 #311842tromicPartecipanteI am not sure if I understand where this part should come?
Non sono sicuro se ho capito dove questa parte dovrebbe venire?12 Agosto 2013 alle 16:03 #311843020DaniloPartecipantePer Lulazz,
….Ho voluto solo far vedere il principio di funzionamento…il nottolino puo essere fatto in mille modi diversi…compreso una pretuberanza che puoì essere parte della boccola d’ammortizzo per tutti quelli che anelano per avereuna testata piu’ piccola possibile…..faro’ il disegno per la testata che sto facendo con il pistone ammortizzatocon canna 14…..stai tranquillo che non si spostera’ mai niente, il silicone aderisce come una ventosa e sifa fatica a spostarlo e a posizionarlo con le mani….come scorrisagola lo vedrei piuttosto sconveniente…Per Tekel,
..il tubo e’ tagliato con un tornio ma puo essere fatto anche con il trapano e un taglierino…non c’e’
bisogno di essere precisissimi anche perche’ tutti i tubi hanno un raggio di curvatura e quindi e’
impossibile tagliarlo perfettamente dritto….
.
for Tromic,
….I’ll post a drawing of the head I’m about to make…..all I wanted to show is that the vaacum can be achieved with a simple 6mm tube of silicon/EPDM/PTFE (better 6.35mm)etc etc….the advantage is that it can be used with 6.5/6.75/7mm shafts with both free and with slider….all you have to do is pulling up or down the tube on the device to change the hole width…ie: in the second pic the tube is pulled up enough to accomplish the vaacum with a 6.5mm shaft….in the third pic the tubing is pulled down and the hole got wider in order to get the vaacum with a 7mm shaft….12 Agosto 2013 alle 17:38 #311844tromicPartecipante@020Danilo wrote:
…
for Tromic,
….I’ll post a drawing of the head I’m about to make…..all I wanted to show is that the vaacum can be achieved with a simple 6mm tube of silicon/EPDM/PTFE (better 6.35mm)etc etc….the advantage is that it can be used with 6.5/6.75/7mm shafts with both free and with slider….all you have to do is pulling up or down the tube on the device to change the hole width…ie: in the second pic the tube is pulled up enough to accomplish the vaacum with a 6.5mm shaft….in the third pic the tubing is pulled down and the hole got wider in order to get the vaacum with a 7mm shaft….I see… It would be similar principle to this early Tomba, but nicer:
Capisco … Sarebbe principio simile a questa precoce Tomba, ma più bello:
http://forums.deeperblue.com/pneumatic-spearguns/81791-tomba-all-one-barrel-sealing-3.html#post76061112 Agosto 2013 alle 17:45 #311845020DaniloPartecipante…Yes Tromic it is similar……
…questo e’ solo un esempio di come potrebbe essere utilizzato questa tenuta stagna….
13 Agosto 2013 alle 5:38 #311846tromicPartecipanteAwaiting for your workmanship and results!
Attesa per la lavorazione e risultati! 😀18 Agosto 2013 alle 9:33 #311847020DaniloPartecipanteIl silicone e’ un materiale molto flessibile, ha un effetto ventosa su
quasi tutti i materiali ma, se viene lubrificato, diventa uno dei materiali piu’ scorrevoli.
Questo e’ un tubo con dimensioni interne da 6mm, ho introdotto prima un’asta da 6.5mm
poi una da 7mm e, infine, un’asta con codolo stc per scorrisagola…[video]http://youtu.be/CpCTctLmqFs[/video]
18 Agosto 2013 alle 9:33 #311848020DaniloPartecipante[youtube:bxbki0sn]CpCTctLmqFs&feature[/youtube:bxbki0sn]…pardon
19 Agosto 2013 alle 19:17 #311849tromicPartecipanteGood work Danilo! Gun for all spears.
Buon lavoro! Pistola per tutte le lance. 🙂20 Agosto 2013 alle 4:54 #311850020DaniloPartecipante…Tks Tromic…..yes, silicon, when lubricated, is so sliding that you can change the shaft without changing hole width by pulling up or down the silicon ruber…with 6.5mm or 7mm shafts you can’t
feel any friction variation……now we have to find out if it holds hundreds shots…….il silicone, se lubrificato, e’ cosi scorrevole che puoi cambiare asta senza variare la
larghezza del foro spingendo su e giu’ il pezzo di tubo in silicone…cambiando asta non
si avverte alcuna differenza…ora si dovra’ stabilire se e’ anche duraturo….20 Agosto 2013 alle 5:12 #311851tromicPartecipante@020Danilo wrote:
…Tks Tromic…..yes, silicon, when lubricated, is so sliding that you can change the shaft without changing hole width by pulling up or down the silicon ruber…with 6.5mm or 7mm shafts you can’t
feel any friction variation……now we have to find out if it holds hundreds shots…….il silicone, se lubrificato, e’ cosi scorrevole che puoi cambiare asta senza variare la
larghezza del foro spingendo su e giu’ il pezzo di tubo in silicone…cambiando asta non
si avverte alcuna differenza…ora si dovra’ stabilire se e’ anche duraturo….I remember, I also liked that very early solution of mine because it was very simple. It was working fine and I used it only with free shaft, but I prefere shaft with slider.
Mi ricordo, mi piaceva anche molto presto che la soluzione dei miei perché era molto semplice. Si stava lavorando bene e l’ho usato solo con asta nuda, ma ho prefere asta con di scorrisagola.
20 Agosto 2013 alle 5:28 #311852020DaniloPartecipante…I’m going to use it with slider, I don’t like free shaft….
20 Agosto 2013 alle 7:25 #311853tromicPartecipante@020Danilo wrote:
…I’m going to use it with slider, I don’t like free shaft….
That would be than one step further than I did. In such design Polyurethane tubing on shaft end would be useful. Than you should not use metal ring.
Questo sarebbe di un ulteriore passo avanti di me. In tale disegno Tubi in poliuretano sul lato albero sarebbe utile. Che non si dovrebbe usare l’anello di metallo. 🙂 -
AutorePost
- Devi essere connesso per rispondere a questo topic.